Got 2000 bullets for 5.56 loads in today.
total cost of bullets + powder + brass?
Got 2000 bullets for 5.56 loads in today.
Have you considered powder coating your bullets. I have been doing it with great results. I have recovered fired bullets and the coating is still on even after firing through a 2x4.Started breaking in a couple of new (to me) bullet molds.... a heavy 357 and a light 45...
The 357 is a two cavity, and the 45 is a 4 cavity. Didn't do a whole bunch, about 70 of each, but it will give me enough to evaluate them.
The 357 is a fat heavy.... drops right at .360 (perfect)... .it's supposed to be 180gr, but I didn't weigh any. My scale was put up, out of the way of melted lead.
The 45 drops at .453-4, and weighs right at 235gr.
Both are the "tumble lube" style lube grooves. I had shot about 10 of the 45's a couple of weeks back, and they showed a lot of promise. I'm looking forward to trying out the heavy 357...
Too much fun....
Started breaking in a couple of new (to me) bullet molds.... a heavy 357 and a light 45...
The 357 is a two cavity, and the 45 is a 4 cavity. Didn't do a whole bunch, about 70 of each, but it will give me enough to evaluate them.
The 357 is a fat heavy.... drops right at .360 (perfect)... .it's supposed to be 180gr, but I didn't weigh any. My scale was put up, out of the way of melted lead.
The 45 drops at .453-4, and weighs right at 235gr.
Both are the "tumble lube" style lube grooves. I had shot about 10 of the 45's a couple of weeks back, and they showed a lot of promise. I'm looking forward to trying out the heavy 357...
Too much fun....
I experimented with PC back when it was just becoming a "thing".... I had ok results, but for some reason, couldn't get a consistent layer... most looked ok, but some were thicker than others..Have you considered powder coating your bullets. I have been doing it with great results. I have recovered fired bullets and the coating is still on even after firing through a 2x4.
Sure... we just need to figure out a time that's convenient. I'm certainly no pro at it, but I can muddle my way through...Would you consider doing a casting session with me? I have a ton of casting stuff but don't recall how to do it. My brother in law taught me once upon a time, but, meh.
Another member was going to teach me but he disappeared.
I bought a Harbor freight rock tumbler and made a 4 inch pvc tumbler tube. I had to use a angle grinder cut off wheel to modify the frame a little. I put a 4 inch pipe plug in each end of the tube and added a good hand full of lead cast bullets and about ¾ cup of quality powder coating powder. I also add a hand full of plastic pellets use in the airsoft guns. They help add a static charge to the slugs. I then dump them into a plastic bowl and use a small side cutter pliers to pick them out by their lube ring and place them on a silicone sheet sitting in a toaster oven pan. I stand them on their flat back end and slide them into the toaster oven. 20 minutes at around 275 F and then drop them into cold water. I get a very even coat on all the bullets. I then run them all through a Lee bullet sizer. After sizing they are ready to load. When fired the powder coat does not even come off the bullets at all. Like I said I have shot them through a 2x4 and the powder coating is still attached. Absolutely no leading of the barrel. I have pictures of the finished bullets before and after firing. I think the quality of your powder coating powder is very important. None of the Harbor freight powders will work.I experimented with PC back when it was just becoming a "thing".... I had ok results, but for some reason, couldn't get a consistent layer... most looked ok, but some were thicker than others..
I've been reading up on it, and it seems that a lot of the early bugs have been worked out, so I've been considering trying again. I need to get another convection oven... mine sort of disappeared...
I guess you do the shake and bake method? I had even considered getting a PC gun from Harbor Freight back then, but didn't have the room to set up a spray booth kind of thing...
Bullets cost 11.1 cents, powder is 11.5 cents, cases I pick up off the ground, primer are from an old stash, but I would estimate at 10 cents each to replace.total cost of bullets + powder + brass?
Bullets cost 11.1 cents, powder is 11.5 cents, cases I pick up off the ground, primer are from an old stash, but I would estimate at 10 cents each to replace.
Total cost is about 33 cents shipped to my door. I will keep an eye out for deals on shipping next time.
I tried HF powder, and had mixed results with it. I then bought some from an online guy... can't remember who, now.... that powder was much higher quality.I bought a Harbor freight rock tumbler and made a 4 inch pvc tumbler tube. I had to use a angle grinder cut off wheel to modify the frame a little. I put a 4 inch pipe plug in each end of the tube and added a good hand full of lead cast bullets and about ¾ cup of quality powder coating powder. I also add a hand full of plastic pellets use in the airsoft guns. They help add a static charge to the slugs. I then dump them into a plastic bowl and use a small side cutter pliers to pick them out by their lube ring and place them on a silicone sheet sitting in a toaster oven pan. I stand them on their flat back end and slide them into the toaster oven. 20 minutes at around 275 F and then drop them into cold water. I get a very even coat on all the bullets. I then run them all through a Lee bullet sizer. After sizing they are ready to load. When fired the powder coat does not even come off the bullets at all. Like I said I have shot them through a 2x4 and the powder coating is still attached. Absolutely no leading of the barrel. I have pictures of the finished bullets before and after firing. I think the quality of your powder coating powder is very important. None of the Harbor freight powders will work.
I use a 20.00 toaster oven from Walmart and it work just fine. I powder coat my fishing jigs in it also. You will need some silicone baking sheets to set the bullets on. I use a small set of side cutters from Harbor freight to grab the powdered coated bullets by their lube grove to set them on the silicone sheet. The tumbler is the clue to give the bullets a static charge so the powder sticks to the slugs while you are setting them on the sheet. This is what a coated bullet looks like. No lube needed they just need to be sized before loading.I tried HF powder, and had mixed results with it. I then bought some from an online guy... can't remember who, now.... that powder was much higher quality.
I might just have to pick up a little oven on the way home today, and give it a whirl, so to speak....
No better time than the present...
What pressure signs?Been loading 6.5 cm in alpha brass and having pressure problems on even moderate charge weights. I think some of it is tight chamber on Christensen arms MPR and some of it could be thick brass. I might have to get a neck turner