Well, to be fair, a ~90-hp 4-cyl. Iron Duke engine in a 3000 pound F-body is a pretty forgettable combination.I must confess that I can't remember the 4 cylinder offering in them.
Well, to be fair, a ~90-hp 4-cyl. Iron Duke engine in a 3000 pound F-body is a pretty forgettable combination.I must confess that I can't remember the 4 cylinder offering in them.
Axxe55,
For those of us who are over 70YY, the band might not be rock of any sort & likely in TX could well be THE TEXAS PLAYBOYS.
(I'd guess that I've danced, since the 1960s, at least 100 miles to SAN ANTONIO ROSE & to FADED LOVE.)
Of course, I'm just an NETX hillbilly, who once patronized THE RIO PALM ISLE BALLROOM in Longview & was known to go to THE LOUISIANA HAYRIDE on dates.
yours, satx
4.
And I got it wrong. Obviously, you knew that. The 4-cylinders didn't come along until the next gen, starting in 1982.
Well, to be fair, a ~90-hp 4-cyl. Iron Duke engine in a 3000 pound F-body is a pretty forgettable combination.
It was also the same engine used in the Fiero as well. They were incredibly stout engines as well. There are some racers having modified the head, added turbos and intercooling, fuel injection that have achieved well over 800 horsepower on the stock lower end and block.
Axxe55,
Fyi, MANY an IRON DUKE has been "marinized" to pull a bait shrimper or another workboat. = NO tougher service than that, as the engine is under constant load.
yours, satx
Many a Mopar 383 powered farm irrigation systems.I have no idea, but with many other applications that were non-automotive, it's very possible since that engine was a very massed produced engine for GM.
In it's beginning from 1977 to 1981 were fitted with carburetors, and in 1982 with a TBI system to 1993 when it was phased out for the Chevrolet 2.2 Ecotec engine.
Marine applications are sort of unique in their own way. Pretty much any and every automotive engine at one time or another has been used in a marine application. Mercruiser used a LOT of various GM engines for their marine applications. Chrysler and Ford engines were very common for marine applications. Volvo, Saab, Mercedes, Nissan, Detroit Diesel, Cummins, Rolls Royce, and many, many more.
Many a Mopar 383 powered farm irrigation systems.
I have no idea, but with many other applications that were non-automotive, it's very possible since that engine was a very massed produced engine for GM.
In it's beginning from 1977 to 1981 were fitted with carburetors, and in 1982 with a TBI system to 1993 when it was phased out for the Chevrolet 2.2 Ecotec engine.
Marine applications are sort of unique in their own way. Pretty much any and every automotive engine at one time or another has been used in a marine application. Mercruiser used a LOT of various GM engines for their marine applications. Chrysler and Ford engines were very common for marine applications. Volvo, Saab, Mercedes, Nissan, Detroit Diesel, Cummins, Rolls Royce, and many, many more.
Was a good engine with good power. Four barrel Holley, if I recall.Yes they did! I have worked on few of them over the years.
Axxe55,
GRANTED. Though the IRON DUKE is the only automotive engine (that I can think of) that is routinely used in commercial workboat applications W/O being built or rebuilt with "marine grade" internal parts.
IF you go down to the commercial fish docks on the TX coast, you will see any number of Iron Duke engines, which have had NOTHING done to them for marine applications, except being fitted with a flame arrestor for the carb, a marine reverse gear fitted to the engine & a "dry stack exhaust" installed.
yours, satx
In reality, there are for the most part, no internal mods done to most automotive engines for marine applications. Most of the modifications are safety related to the fuel, ignition and exhaust systems for use in an enclosed environment, or having to meet Coast Guard safety regulations for marine applications.
For newer bowtie-based motors, many builders will make the tolerances slightly looser for marine duty, due to higher loads and rpm.
But a lot of folks just run passenger car crate motors.
Sent from my iPhone using Tapatalk Pro
The vast majority of all the "marine" engines I have been into for rebuilds or repair, they pretty much had stock internals, with the exception of purpose built racing engines.
Even the Oldsmobile 455 that powered my jet boat I had many years ago, other than the aluminum intake and Holley four barrel, and the water-cooled exhaust manifolds was stock internally.