To Oil or Not to Oil
- Thread starter Dancing Heretik
- Start date
True. I reserve it for when I’m in a hurry. I don’t think it’s as bad as you think. If a part is soaked with cleaner, and after spraying it down, you just get the left over with a rag or q-tips.
it’s not that hard to keep your air dry and drain your tank after each use.
Last edited:
Back in the '80s when gun mags gave us the latest bad gun care ideas, one scare was how lube on your gun was seeping into your ammo and when needed your gun would go pffffht instead of bang. Since I was a policeman this was an article I read with gusto and a cup of coffee. Have always been very anal about keeping my gun clean. For 5 years I cleaned my 4506 S&W dry then covered it in Remington Dri lube which was basically silicone spray. The silicone came in a carrier that turned whitish when it dried. Then I'd wipe off the white and continue with life. I also had a personal policy that when qualifying I shot from my holster without any prepping of the gun. Never had a non ammo related failure, never. I learned from this that we should lube our guns with a quality gun related product because it takes such a tiny amount you will retire before you buy more than a few containers. And your gun will last forever
TexasGunAdmirer
New Member
I use a quality gun oil and lightly lubricate as shown in the owner’s manual and on any wear spots. I use a cotton swab dipped in gun oil to control application.
In my Texas LTC classes I sometimes see bone dry handguns that are not operating as smoothly as they should. It makes a difference in how smoothly and reliably some guns operate. A lack of lubrication also makes some parts wear faster.
Seems like most people do not lubricate guns at all or over lubricate them. Not many do it just enough.
In my Texas LTC classes I sometimes see bone dry handguns that are not operating as smoothly as they should. It makes a difference in how smoothly and reliably some guns operate. A lack of lubrication also makes some parts wear faster.
Seems like most people do not lubricate guns at all or over lubricate them. Not many do it just enough.
I finally oiled my AR last Saturday afternoon.
Had multiple malfunctions that night. Oiling it was obviously the cause of the malfunctions. Had no issues at all in the previous thousand or so rounds of suppressed fire with 0 maintenance.
Sent from my iPhone using Tapatalk
Had multiple malfunctions that night. Oiling it was obviously the cause of the malfunctions. Had no issues at all in the previous thousand or so rounds of suppressed fire with 0 maintenance.
Sent from my iPhone using Tapatalk
TheMailMan
TGT Addict
2 things.
First, shoot it long enough for the barrel to get hot and let the smoke from the oil burning off get in to your eyes. It will ruin a range qualification. Ask me how I know.
Second, notice they didn’t allow any of those oily ass guns to come in contact with all that dirt and sand around them. To much oil on a gun will do a magnificent job of holding on to every bit of dust that it comes in contact with.
You don’t want too much oil on your guns. I bet they get a lot of views, but they are giving bad information.
Sent from my iPhone using Tapatalk
HKShooter65
TGT Addict
Similar to a thread I started a while back.
I question the utility of cleaning a bore if it's shooting just fine.
If I want to get a firearm mechanism really really clean (the lazy way) I blast it with automotive brake cleaner.
Blow it away with compressed air.
DO NOT get it on finished stocks or plastics.
My favored lube is a combination of Birchwood Casey Barricade for metal and blued surfaces.
It's never failed me.
And....
A have a couple of quarts of 10w60 synthetic motor oil left over from when I once owned a BMW M5.
That is for when I feel the need for actually oily protection like inside the roller locks and trunion on my old HK long guns or to lightly coat an AR piston and carrier when thoroughly cleaned.
Mostly I just spritz everything with the Barricade Birchwood Casey stuff the lazy way.
I question the utility of cleaning a bore if it's shooting just fine.
If I want to get a firearm mechanism really really clean (the lazy way) I blast it with automotive brake cleaner.
Blow it away with compressed air.
DO NOT get it on finished stocks or plastics.
My favored lube is a combination of Birchwood Casey Barricade for metal and blued surfaces.
It's never failed me.
And....
A have a couple of quarts of 10w60 synthetic motor oil left over from when I once owned a BMW M5.
That is for when I feel the need for actually oily protection like inside the roller locks and trunion on my old HK long guns or to lightly coat an AR piston and carrier when thoroughly cleaned.
Mostly I just spritz everything with the Barricade Birchwood Casey stuff the lazy way.
